1、Alarm mode: set one or more alarms per day (up to 4 sets of wake-up time), wake up automatically at the set time, and sleep after sending location data.
2、Timer mode: send back the location data according to the set time.
3、Day of the week mode: you can set a time point and select the day of the week or days of the week to send location data and then sleep.
4、GPS positioning + WIFI + base station positioning: first GPS-WIFI-base station daily wake-up wifi-base station car chase GPS-WIFI-base station (priority from left to right)
5、Timer: RTC clock in the device
6、Anti-tampering alarm: the device automatically detects the light level from dark to bright and immediately reports the tampering alarm to the platform.
HC113 Wireless ultra-long standby positioning device
description
- Product Introduction
- frequently asked questions
- precautions
1、Size: 764124mm
2、Weight: 106g (including battery)
3、Working voltage: DC 3V
4、Working current ：75-100mA
5、Standby current ：2uA
6、Built-in battery: Cylindrical lithium manganese dry battery
7、Battery operating time: 3 years of continuous use with new batteries
8、Operating temperature: -25°C to +80°C
9、Storage temperature: -25°C to +85°C
10、Communication Network: 4G Full Netcom
11、Capture Sensitivity: -143dB
12、Tracking sensitivity: -159dB
13、Cold start time: -38s
14、Hot start time: -2s
15、GSM Antenna: Built-in
16、GPS Antenna: Built-in
17、LED Indicator: Power, status indication
18、Transmission Protocol: UDP/TCP depending on the communication protocol
19、Positioning mode: WIFI+GPS+BeiDou+base station positioning+EPO
20、Anti-tampering mode: Light-sensitive anti-tampering model
21、Positioning error: WIFI <5 meters, GPS <10 meters (positioning error is related to the terrain and time of the vehicle’s location)
22、GPRS: Class12 TCP/IP buildFrequently Asked Questions Fault Description Handling method Poor positioning signal Using the terminal in areas with poor reception, such as underneath a tall building or in a basement, it cannot effectively receive satellite airwaves. Use the terminal in a place with good signal. Unable to turn on the computer Repeated switching on and off, the indicator light does not light up Turn on the terminal after 10 seconds with the switch turned OFF. Unable to connect to the network SIM card is not properly installed Check the SIM card and reinstall it. Dirt on the metal surface of the SIM card Please wipe it with a clean cloth. IM card is damaged or invalid Replace the SIM card with a valid one Contact your service provider Out of GSM service area Move to the service area of your network service provider Weak signal Please move to a place with strong signal and try again Can't find the location information GPRS service is not enabled on the SIM card Please contact your network service provider Enable GPRS service SIM card is in arrears Recharge fee Send command to modify the parameter does not change Wrong command format Please edit the command again and send it again No reply to sent command Please make sure the terminal can connect to the network normally and enable the SMS function of the terminal SIM card. 1. Please pay attention to waterproof for electronic products.
2. Please insert the SIM card before installation and make sure the SIM card is not set with password, otherwise the device can not work normally.
3. The USB port on the terminal device is for factory testing only, not for charging the device, please do not use it for charging or other purposes.
4. The installation location must be above a place that is not covered by electromagnetic wave-absorbing substances (e.g., metal, explosion-proof heat insulation film).
5. Do not expose the device to liquids or operate with wet hands.
6. Do not put the device into fire
7. The device may not work when the temperature is lower than -20℃ or higher than +60℃.
8. When the vehicle is in the underground parking lot, tunnel or garage, it will affect the positioning signal. When the vehicle is in underground parking lot, tunnel or garage, it will affect the positioning signal, and there may be a blind area of communication network signal that causes the device can not monitor; when the vehicle drives out of the above area, the device will automatically return to normal work.
9. Do not repair the device by yourself when it encounters abnormal conditions. The manufacturer is not responsible for any damage caused by connecting non-original accessories or unplugging connections between parts.
10. This product is a safe driving aid, and we are not responsible for any damage caused by malfunction or loss of information.
11. This product has passed the international CE certification, but because of the complexity of the electromagnetic environment in the car, this product may cause electromagnetic interference with the electrical equipment in the car in some models.
12. Do not install or operate this product while the vehicle is in motion.
13. Do not connect the uninterruptible power supply without authorization, as this may cause the vehicle or the product to malfunction, and be sure to consult a professional regarding installation.
14. Do not subject the product to strong shocks or vibrations, which may damage the product and cause it to malfunction or become inoperable.
15. The temperature range for normal functioning of the product is from -20 degrees Celsius to 65 degrees Celsius, beyond which the product may malfunction, catch fire or explode.
Related Solutions
-
Cargo/Asset Security Solutions
Innovatech specializes in research and development for containers, packages, valuable assets, cold chain, as well as land transportation and Cargo tracking tool for various scenarios such as shipping, ensuring the transportation safety of the entire cargo process and at each node
-
UBI Auto Insurance IoT Solution
Based on core technologies such as inertial guidance and driving behavior analysis, empowering enterprises to build UBI risk models driven by data, innovate auto insurance products and increase profitability